How do you use a lawn genie?

Programming a Lawn Genie

Plug the unit into the wall outlet.
Set the day by pressing the CLOCK key two times, then press the HRS button until the proper number for the day of the week displays.
Set the frequency of watering for A and B programs by setting the switch for each under SELECT 7 DAY KEYPAD.

How do you adjust the genie l7034?

Simply remove the cover from the canister and start adjusting.

Locate the black flow control screw on the head of the valve and turn it clockwise with a screwdriver until you completely close the valve.
Turn on the water supply to the irrigation system via the water shut-off valve.

How does a lawn genie valve work?

The Lawn Genie L7034 Anti-Siphon Valve is equipped with a flow-control screw so you can easily adjust the rate the sprinklers emit water. The flow-control screw adjusts the amount of water pressure that goes to the sprinkler zone serviced by the valve.

How do I manually start my sprinkler system?

Turn the pliers or wrench counterclockwise to open the valve. If you have a cross-shaped valve handle, stick the prongs of a sprinkler valve key around the cross and turn the key counterclockwise to activate the valve. For round knobs, grip the knob with your hand or a clean rag and turn counterclockwise to activate.

How do I bleed my irrigation system?

Bleed your sprinkler system to avoid any potential problems. Bleeding, or “winterizing” your home’s sprinkler system is one way to protect your sprinkler system from freezing during winter. An easy way to do this is by draining the pipes and then blowing it out to dry with an air compressor.

Why does my sprinkler system not turn on?

Backflow Device Valves If your sprinkler system won’t turn on or if you have low water pressure, this could be caused by the valves not being turned on all the way. Just locate the valves and make sure they are both turned on (you should have 2 valves, one located on the horizontal pipes and one for the vertical ones).

How do you manually turn on a Lawn Genie valve?

Similarly, it is asked, how do you manually turn on a lawn genie valve? Manually open the valve by turning the bleed screw counterclockwise 1/2 turn. To close the valve, turn the bleed screw clockwise.

Is there a problem with my Lawn Genie sprinkler system?

Problems in Lawn Genie sprinkler valves can usually be isolated to either the timer or the valve solenoid. Manually open the valve handle, and determine if water is flowing into the circuit.

How to adjust the pressure in Lawn Genie l7034 anti?

Turn the water supply back on. Locate the manual-bleed screw, the smaller of the two black screws near the solenoid. Turn the manual-bleed screw counterclockwise using the screwdriver until water flows through the valve. Turn the flow-control screw slowly until the you get the desired flow rate.

How much water does a Lawn Genie mist?

This misting means higher water usage and more water on the lawn near the sprinkler head. You can adjust the flow rate from 0.25 to 25 gallons per minute.

Is there a manual for my Lawn Genie?

If the manual for your controller shows a different model on the front page, do not be concerned. Although the instructions are written for another controller, they will still apply to your model. If the manual you are looking for is not listed here, Contact Us with your information or call (800)231-5117 to request one.

How does a Lawn Genie sprinkler valve work?

Likewise, how does Lawn Genie valve work? The Lawn Genie L7034 Anti-Siphon Valve is equipped with a flow-control screw so you can easily adjust the rate the sprinklers emit water. The flow-control screw adjusts the amount of water pressure that goes to the sprinkler zone serviced by the valve .

What’s the best time to start a Lawn Genie?

When setting the start time for each zone, allow enough time between start times so there is no overlap. For instance, if Zone 1 is programmed to start at 8 AM and run for 20 minutes then Zone 2’s start time should be at least 21 minutes later.

How do you use a lawn genie?